VisualizationTea and Coffee Organizer SVG, Coffee Stick Holder Laser Cut File, Five Section Tea Box DXF, Hot Drink Caddy
A five-section tea and coffee organizer with three narrow slots at the back for coffee and sugar sticks and two wide sections at the front for envelope tea bags. The free download contains SVG and DXF files for 3, 4, 5 and 6 mm plywood; the box is 300 × 200 × 90 mm (11.81 × 7.87 × 3.54 in), assembles from 9 pieces with tabs and slots, and its sides slope from a 90 mm back to a 54 mm front.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 300 × 200 × 90 mm (11.81 × 7.87 × 3.54 in)
- Parts
- 9
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,020 × 302 mm
- Cut length
- 6.29 m
- Est. time, 10 W diode (3 mm)
- 20 min 58 s
- Est. time, 40 W CO2 (3 mm)
- 8 min 44 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Choose the plywood thickness you will use, open that SVG or DXF, and cut one test slot to check the joint fit.
- 02Cut all nine parts, splitting the 1020 mm layout over two sheets on a small bed.
- 03Assemble the box walls on the base, insert the cross divider, add the single front divider, then the two tall dividers at the back.
- 04Sand, finish with lacquer or oil, stand coffee sticks in the three back slots and file tea bags in the two front sections.
Wide in front, narrow behind
Tea bags in square envelopes need width; coffee sticks need height. This box gives each what it needs. A full-width cross divider, 73.5 mm tall, sits a little behind the middle. In front of it a single divider splits the row into two wide sections, each about half of the 300 mm width and roughly 111 mm deep, sized for envelope tea bags lying back against the divider. Behind it, two full-height dividers make three slots about 92 mm deep for sticks that stand upright against the 90 mm back wall.
The photo shows instant coffee sticks, latte sticks and gold espresso sticks in the three back slots, and green tea and chamomile filling the two big front sections. Five compartments is a sensible number for one household: two teas you drink daily, three kinds of coffee or sugar.
Laser notes
All nine parts of the 3 mm file sit on a 1020 × 302 mm sheet. On a bed narrower than that, cut the base and back in one job and the side panels, front and dividers in another. A 40 W CO2 cuts the 3 mm file in about 8 min 44 s and a 100 W CO2 in about 4 min 12 s; on a 10 W diode allow about 20 min 58 s. A 10 W diode is happiest with 3 mm; for 5 or 6 mm plywood, switch to a CO2 or accept several slow passes.
Only three dividers sit inside, so assembly is quick: cross divider first, then the front divider, then the two back ones. A spot of glue under each makes the box permanent if you want it.
Gift ideas
Fill it with two favourite teas and three coffees for a new neighbour, sell it as a breakfast caddy alongside a matching napkin box, or offer a painted version for a coffee corner in a small office. Sand the edges and seal the box with a clear finish before use.
Questions about this file
What goes in the narrow back slots?
They suit upright stick sachets such as instant coffee, latte and sugar sticks, which lean on the 90 mm back wall.
Will large tea envelopes fit at the front?
Yes, each front section is about half the box width and around 111 mm deep, enough for standard square tea envelopes.
Will a scaled-down version still go together?
Scale the overall outline, then reset every slot to your exact plywood thickness so the tabs still lock.
Should I glue it?
Not necessarily; the tab-and-slot joints hold, and glue simply makes the box permanent.
How do I waterproof it for the kettle corner?
Two thin coats of water-based polyurethane or a hard-wax oil protect it from steam and drips.
Similar files
