VisualizationWasp SVG Laser Cut File, Realistic Insect Ornament DXF, Entomology Gift, Curiosity Cabinet Wall Decor
A realistic common wasp (Vespula vulgaris) drawn at a diagonal, with a striped abdomen, a solid dark thorax and one long wing showing its vein cells. The one-piece file measures 90 × 88.5 mm (3.54 × 3.48 in). The 4 mm hole is at the wing tip, so the insect hangs head down like a pinned specimen.
- Formats
- SVG, DXF
- Size
- 90 × 89 mm (3.54 × 3.48 in)
- Parts
- 1
- Hanging hole
- 4 mm
- Cut length
- 0.48 m
- Engraving area
- 11.9 cm²
- Material
- 3 mm plywood, MDF or acrylic
- Est. time, 10 W diode
- 3 min 34 s
- Est. time, 40 W CO2
- 1 min 19 s
- Est. time, 100 W CO2
- 49 s
- Per 300 × 400 mm sheet
- 12 pcs
- Per 600 × 400 mm sheet
- 24 pcs
- Layers
- CUT (red), ENGRAVE (black)
- License
- CC0 1.0: free for personal and commercial use
Free account required to download
How to make it
- 01Import at actual size, 90 × 88.5 mm, and make sure the wing tip with the hole sits at the top.
- 02Run the engraving first: a solid fill for the thorax and abdomen bands, and the same pass picks up the fine wing veins.
- 03Cut the outline last, and test one piece to see that each leg and antenna comes free without charring through.
- 04Lift the wasp out by the body rather than by a leg, sand the back, and hang it from the wing-tip hole.
A specimen, not a cartoon
Insect files are usually cute bees with smiles. This one is closer to a museum drawing. The wasp walks diagonally across the piece, head towards the lower right. The abdomen is divided into engraved segments with lighter bands between them, the thorax and head form a solid dark mass, and one long wing lies along the upper edge with a network of veins drawn in thin lines near the tip. Antennae and legs reach out in different directions, each with a visible joint, and the outline follows every one, so the silhouette alone is unmistakably a wasp.
Thin limbs and wing veins
Legs and antennae are long, narrow strips of wood. The cut has to be clean but not overpowered, or the strips scorch right through their width. Birch plywood is the safest choice; MDF can snap at the knees. The wing veins are fine engraved lines, and a quick scan keeps them sharp. Estimated times in 3 mm plywood: 10 W diode, 3 min 34 s; 40 W CO2, 1 min 19 s; 100 W CO2, 49 s.
Buyers for an insect ornament
- Entomology students, beekeepers and pest-control firms looking for a quirky branded gift.
- Cabinet-of-curiosities decor: mount several on a board with engraved Latin labels.
- Halloween and creepy-crawly themes, alongside spiders and beetles.
- Nature centres and science teachers, as a hands-on model of head, thorax and abdomen.
Questions about this file
Is it accurate enough for teaching insect anatomy?
It shows the three body sections, the jointed legs, the antennae and the wing venation clearly, so it works as a simple visual aid. It is a decorative drawing rather than a scientific diagram, so add labels yourself.
Will the legs snap off?
In birch plywood at full size they are reasonably sturdy, but they are the thinnest parts of the piece. Avoid MDF, sand with the grain, and pack the wasps flat rather than loose in a bag.
Can I make it look like a framed specimen?
Yes. Glue it into a shadow box over light card, or cut a simple backing plate and add a small engraved label with the Latin name, Vespula vulgaris.
Does it work in yellow acrylic?
Yellow acrylic with a dark engrave gives a striking wasp colour scheme, but acrylic is more brittle at the leg joints. Use cast acrylic and handle the cut piece gently.
Can I sell wasp ornaments or use them as company gifts?
Yes. Commercial use is allowed, so you can sell the pieces, add a logo on the back or include them in branded gift sets.
Similar files
